Protected profile traffic statistics

How to use traffic statistics, which data it includes, and what each chart means.

What traffic statistics are

Traffic statistics are a set of charts that show how much traffic of each type the mitigation system processed using a specific protected profile.

In simple terms, this is DDoS attack statistics. You can see how much malicious and legitimate traffic reached your resource during attacks.

What this statistic includes:

  • Traffic to IP addresses assigned to the protected profile, sent during a DDoS attack.

What this statistic does not include:

  • Traffic to IP addresses assigned to the protected profile, sent under normal conditions, when there is no DDoS attack.

  • Traffic to IP addresses assigned to other protected profiles.

Why does this statistic include this traffic?

This is statistics for traffic processed using a specific protected profile. A profile is used only during a DDoS attack and only to filter packets addressed to particular subnets or sets of IP addresses.

Here is a reminder of how our protection works:

  • Under normal conditions, traffic reaches your servers directly without passing through the mitigation system. When a DDoS attack starts, the route changes: traffic is filtered first and only then reaches your resource.

  • The mitigation system consists of geographically distributed server clusters.

  • Each mitigation-system server is called a scrubber. Its task is to filter DDoS attack traffic using Strictera mitigation software.

  • Protected profiles are installed on each scrubber. A protected profile is a set of traffic filtering rules defined for particular subnets and sets of IP addresses.

  • When traffic passes through the mitigation system, it finds the required profile and filters packets according to its rules.

As a result, the statistics covered in this article include only traffic processed using a specific protected profile: packets sent during a DDoS attack to IP addresses assigned to that profile.

How can I find out which IP addresses are assigned to a profile?

Open Network protection and select Protected profiles. You will see a list of profiles. The IPs column shows the addresses assigned to them.

List of protected profiles

If you need statistics for all inbound traffic, including traffic sent under normal conditions when there is no attack, open monitoring object traffic statistics.

How to open traffic statistics

Go to Network protection → Protected profiles. Select the ellipsis (…) next to the required profile, then choose Traffic statistics.

The page opens with two tabs. Choose the one you need:

  • General statistics contains summary data for all IP addresses and subnets assigned to the protected profile. You can see how much traffic the mitigation system allowed to your servers, dropped, or sent for TCP or DNS authentication. It also shows which security policies were violated by the dropped traffic.

  • Per-host statistics contains data for a specific IP address of your resource. You can see how much traffic reached your IP address after filtering and how much was dropped.

General statistics

The data is divided into two types: Bandwidth and Statistic labels.

Bandwidth

Under Bandwidth, you can see the volume of different traffic types:

  • pass is inbound legitimate traffic allowed to your servers.

  • drop is inbound malicious traffic dropped during filtering.

  • reply is response packets sent by a scrubber to the source. They are sent only when the protection starts a client check: TCP or DNS authentication.

Two charts are available: bits per second (bps) and packets per second (pps). They show the same traffic in different units of measurement.

Bandwidth statistics

Statistic labels

Under Statistic labels, you can see how much traffic:

  • Was blocked for a particular reason.

  • Arrived from IP addresses on the White list. These packets are automatically allowed to your resource.

Statistic label statistics

Two charts are available: bits per second (bps) and packets per second (pps). They show the same traffic in different units of measurement. The data is grouped by labels.

What are labels?

A label is a marker that indicates which rule of the protected profile filtered a packet.

Example: there is a rule that drops fragmented IP packets. This rule has the IP_FRAG label. When the mitigation system receives a fragmented packet, it drops it and adds the following information to the statistics: one packet with the IP_FRAG label.

There are many labels, and each is assigned to its own rule. In the statistics, you can see the volume of traffic marked with different labels.

Traffic from regular users that is allowed to your resource by the mitigation system, except traffic from the White list, is not marked with a separate label. It is not shown on the Statistic labels charts.

The table below lists labels that may occur in different protected profiles. Note the following:

  • Your profile does not contain all labels from the table. It contains only labels that correspond to its rules.

  • Your statistics may contain special labels that are not listed in the table, for example, if your profile has non-standard protection rules.

Label Meaning What happens to this traffic

ACL_ICMP

ICMP traffic other than Echo Request and Echo Reply

Dropped

ACL_PROTO

Traffic using L3 protocols not used for legitimate communication with the protected resource

Dropped

AMP_DNS

Traffic matching the DNS Amplification attack vector

Dropped

AMP_NTP

Traffic matching the NTP Amplification attack vector

Dropped

AMP_OTHER

Traffic matching the UDP Amplification attack vector

Dropped

BLACKLIST

Traffic from IP addresses on the Black list

Dropped

DNS_AUTH

DNS traffic sent for DNS authentication

Depends on the DNS authentication result: allowed if successful, dropped if unsuccessful

FLOOD_DNS

DNS traffic with an abnormal packet size

Dropped

FLOOD_UDP

UDP traffic sent to ports where traffic using this protocol is not expected

Dropped

INCORRECT_ICMP

ICMP packets with an abnormal size

Dropped

INCORRECT_RST

TCP packets with the RST flag and an abnormal size

Dropped

INCORRECT_SYN

TCP packets with SYN flags and an abnormal size

Dropped

IP_FRAG

Fragmented IP traffic

Dropped

POLICER

Traffic exceeding the overall bandwidth limit, which is the maximum traffic allowed to reach your resource, for example 800 Mbps

Dropped

RL_SYN

The source IP address exceeded its limit by sending more TCP SYN packets per second than allowed. The label is assigned to the first packet received above the limit.

Dropped. All traffic sent from this IP address receives the TEMP_BLOCK label and is dropped for the next five minutes.

RL_UDP

The source IP address exceeded its limit by sending more UDP packets per second than allowed. The label is assigned to the first packet received above the limit.

Dropped. All traffic sent from this IP address receives the TEMP_BLOCK label and is dropped for the next five minutes.

SYS_PORT

Traffic with invalid interactions between system ports

Dropped

TCP_AUTH

TCP packets that did not pass TCP authentication

Dropped

TCP_IGNRD

TCP packets that cannot be authenticated: all packets with flags other than SYN or SYN-ACK

Dropped

TEMP_BLOCK

Traffic from an IP address that violated one of the rate limit rules, for example RL_UDP or RL_SYN. The TEMP_BLOCK label is assigned to all traffic sent from this IP address for five minutes after the limit is exceeded.

Dropped

WEB_INVALID

TCP traffic with invalid port interactions

Dropped

WHITELIST

Traffic from IP addresses on the White list

Allowed

Per-host statistics

  1. Enter the IPv4 address, without a mask, for which you want to view statistics. For example: 203.0.113.10.

  2. Select the required period. By default, data for the last seven days is displayed.

  3. Select Show.

Chart settings

Two charts open: the first is in bits per second (bps), and the second is in packets per second (pps). They show the same traffic in different units of measurement. You can see:

  • Traffic after cleaning is traffic allowed to your IP address after filtering.

  • Estimated filtered traffic is traffic dropped during filtering.

Per-host statistics charts